GW Instek MSO-2102EA (CE) MIXED-SIGNAL OSCILLOSCOPES

SPECIFICATIONS GW INSTEK MSO-2102EA MIXED-SIGNAL OSCILLOSCOPES

Channels: 2ch+Ext

Bandwidth (‐3dB): DC~100MHz

Bandwidth Limit (‐3dB): 20MHz

– Vertical Sensitivity

Resolution: 8 bit, :1mV~10V/div

Input Coupling: AC, DC, GND

Input Impedance: 1MΩ// 16pF approx.

DC Gain Accuracy: ±(3%)when 2mV/div or greater is selected; ±(5%)when 1mV/div is selected;

Polarity: Normal & Invert

Maximum Input Voltage: 300Vrms, CAT I

Offset Position Range:

1mV/div ~ 20mV/div : ±0.5V

50mV/div ~ 200mV/div : ±5V

500mV/div ~ 2V/div : ±25V

5V~10V/div : ±250V

Waveform Signal Process:

+, ‐, ×, ÷, FFT, FFTrms ,User Defined Expression.

FFT:1Mpts

FFT:Spectral magnitude. Set FFT Vertical Scale to Linear RMS or dBV RMS, and FFT

Window to Rectangular, Hamming, Hanning, or Blackman‐Harris.

– Trigger 

Source: CH1, CH2, CH3, CH4, Line, EXT*, *dual-channel models only

Trigger Mode: Auto (supports Roll Mode for 100 ms/div and slower), Normal, Single Sequence

Trigger Type: Edge, Pulse Width(Glitch), Video, Pulse Runt, Rise & Fall(Slope), Alternate, time out, Event‐Delay(1~65535 events), Time‐Delay(Duration,4nS~10S), Bus

Holdoff range: 4ns~10s

Coupling: AC,DC,LF rej. ,HF rej. ,Noise rej.

Sensitivity: 1div

– External Trigger GW Instek MSO-2102EA

Range: ±15V

Sensitivity: DC ~ 100MHz Approx. 100mV; 100MHz ~ 200MHz Approx. 150mV

Input Impedance: 1MΩ±3%~16pF

– Horizontal 

Time base Range: 1ns/div ~ 100s/div (1‐2‐5 increments). ROLL: 100ms/div ~ 100s/div

Pre‐trigger: 10 div maximum

Post‐trigger: 2,000,000 div maximum.

Time base Accuracy: ±50 ppm over any ≥ 1 ms time interval

Real-Time Sample Rate: Max.:1GSa/s (4ch model). Per channel 1GSa/s (2ch model)

Record Length: Max:10Mpts

Acquisition Mode: Normal, Average, Peak Detect, Single

Peak Detection: 2ns (typical)

Average: selectable from 2 to 256

– X‐Y Mode

X‐Axis Input: Channel 1; Channel 3*

*four channel models only

Y‐Axis Input: Channel 2; Channel 4*

*four channel models only

Phase Shift: ±3° at 100kHz

– Cursors and Measurement

Cursors: Amplitude, Time, Gating; available;Unit:Seconds(s),Hz(1/s) ,Phase(degree) ,Ration(%)

Automatic Measurement:

38 sets: Pk‐Pk, Max, Min, Amplitude, High, Low, Mean, Cycle Mean, RMS, Cycle RMS, Area, Cycle Area, ROVShoot, FOVShoot, RPREShoot, FPREShoot, Frequency, Period, RiseTime, FallTime, +Width, ‐Width, Duty Cycle, +Pulses, ‐Pulses, +Edges, ‐Edges, FRR, FRF, FFR, FFF, LRR, LRF, LFR, LFF, Phase, Cursor measurements

– Control Panel Function 

Auto counter: 6 digits, range from 2Hz minimum to the rated bandwidth

Autoset: Single‐button, automatic setup of all channels for vertical, horizontal and trigger systems, with undo Autoset

Save Setup: 20set

Save Waveform: 24set

– Display 

TFT LCD Type: 8″ TFT LCD WVGA color display

Display Resolution: 800 horizontal × 480 vertical pixels (WVGA)

Interpolation: Sin(x)/x

Waveform Display; Dots, vectors, variable persistence (16ms~4s), infinite persistence

Waveform Update Rate: 120,000 waveforms per second, maximum

Display Graticule: 8 x 10 divisions

Display mode: YT ;XY

– Interface GW Instek MSO-2102EA

USB Port: USB 2.0 High‐speed host port X1, USB High‐speed 2.0 device port X1

Ethernet(LAN) port: RJ‐45 connector, 10/100Mbps with HP Auto‐MDIX

Go‐NoGo BNC: 5V Max/10mA TTL open collector output

Kensington Style Lock: Rear‐panel security slot connects to standard Kensington‐style lock.

– Logic analyser specifications

Sample Rate: Per Channel 1GSa/s

Bandwidth: 200MHz

Record Length: Per Channel 10M pts (max)

Input Channels: 16 Digital (D15 ‐ D0)

Trigger type: Edge, Pattern, Pulse Width, Serial bus (I2C, SPI, UART(RS232/422/485), CAN, LIN), Parallel Bus

Thresholds Quad: D0~D3, D4~D7,D8~D11 ,D12~D15 Thresholds

Threshold selections: TTL, CMOS(5V,3.3V,2.5V), ECL, PECL,0V ,User Defined

User‐defined Threshold Range: ±5V

Maximum Input Voltage: ±40 V

Minimum Voltage Swing: ±250 mV

Input impedance: 101KΩ probe loading 8pF

Vertical Resolution: 1 bit

– AWG  Specifications (MSO‐2000EA only)

Channels: 2

Sample Rate: 200 Msa/s

Vertical Resolution: 14 bits

Max. Frequency: 25 MHz

Standard Waveform: Sine, Square, Pulse, Ramp, DC, Noise

Built‐in ARB Waveform: Sinc, Gaussian, Lorentz, Exponential Rise, Exponential Fall, Haversine, Cardiac

Output Range: 20 mVpp to 5 Vpp, HighZ; 10 mVpp to 2.5 Vpp, 50 Ω

Output Resolution: 1mV

Output Accuracy: 2% (1 kHz)

Offset Range: ±2.5 V, HighZ;±1.25 V, 50 Ω

Offset Resolution: 1mV

+ Sine
Frequency Range: 100mHz to 25MHz

Flatness: ±0.5 dB<15MHz; ±1 dB:15MHz~25MHz( relative to 1kHz)

Harmonic Distortion: ‐40 dBc

Stray (Non‐harmonic): ‐40 dBc

Total Harmonic Distortion: 1%

S/N Ratio: 40 dB

+ Square/Pulse
Frequency Range: 100mHz to 15MHz

Rise/Fall time: <15ns

Overshoot: <3%

Duty cycle: Square:50%;Pulse:0.4%~99.6%

Min. Pulse Width: 30 ns

Jitter: 500 ps

+ Ramp
Frequency Range: 100mHz~1MHz

Linearity: 1%

Symmetry: 0 to 100%

– Frequency Response Analysis GW Instek MSO‐2102EA

Dynamic Range: > 80 dB (typical)

Input and Output Sources: Channel 1 or 2 ( 3 or 4 for the four-channel model)

Frequency Range: 20 Hz to 25 MHz

Number of Test Points: 10 to 90 points per decade

Test Amplitude: 20 mVpp to 5 Vpp into High‐Z ; Fixed amplitude across entire sweep

Test Results: Logarithmic overlaid gain and phase plot

Manual Measurements: Two pairs of tracking gain and phase markers

Plot Scaling: Auto‐scaled during test

– Miscellaneous

Multi‐language menu: Available

operation environment: Temperature: 0°C to 50°C. Relative Humidity ≤ 80% at 40°C or below; ≤ 45% at 41°C ~ 50°C.

On‐line help: Available

Time clock: Time and Date ,Provide the Date/Time for saved data

Dimensions: 384mmX208mmX127.3mm

Weight: 2.8kg

Introduction GW Instek MSO-2102EA

The MSO-2000 series is a mixed-signal oscilloscope, which offers dual analog channels + 16 digital channels or 4 analog channels + 16 digital channels. The MSO-2000 series includes MSO-2000E and MSO-2000EA. MSO-2000E has a built-in 16-channel logic analyzer and MSO-2000EA has a built-in 16-channel logic analyzer and a dual channel 25MHz arbitrary waveform generator. The entire series features bandwidth selections of 200MHz, 100MH, and 70MHz. Dual analog channel models provide 1GSa/s real-time sampling rate per channel; four analog channel models provide 1GSa/s maximum real-time sampling rate. The 8-inch 800*480 TFT LCD and the minimum 1mV/div vertical range allow the MSO-2000 series to measure complex feeble signals and clearly display measurement results.

Features

– 200/100/70MHz bandwidth selections: 2 or 4 channels
– MSO-2000EA equips with a 16-channel logic analyzer and a dual channel 25MHz arbitrary waveform generator
– Real-time Sampling rate for each channel is 1GSa/s (2-channel models); Maximum real-time Sampling rate is 1 GSa/s (4- channel models)
– Maximum 10M memory depth and VPO waveform display technology
– Waveform update rate up to 120,000 wfms/s
– 8 ” WVGA TFT LCD screen display
– Free Frequency Response Analyzer Software
– Maximum 1M FFT provides higher frequency domain resolution measurements
– High Pass, Low Pass and Band Pass Filter Functions
– 29,000 segmented memory sections and waveform search function
– I2C/SPI/UART/CAN/LIN serial bus trigger and decoding functions
– Data log function is able to track signal changes up to 100 hours
– Network storage function