Tiếng Việt
specifications GW Instek APS-7050 AC Power Sources Programmable Linear
Power Rating: 500VA
Output Voltage 0 ~ , 0 ~ 310Vrms
Output Frequency 45.00 ~ 500.0 Hz
Max. Current(rms): *1 0 ~ 155 Vrms 4.2A; 0 ~ 310 Vrms 2.1A
Max. Current (peak):
0 ~ 155 Vrms Peak value which is four times of the maximum current(rms)
0 ~ 310 Vrms Peak value which is four times of the maximum current(rms)
OPT. APS-003(rms): 0 ~ 600 Vrms: 1.05A
OPT. APS-003(peak): 0 ~ 600 Vrms: Peak value which is four times of the maximum current
Total Harmonic Distortion (THD) *2: ≤ 0.5% at 45 ~ 500.0Hz (Resistive Load)
Crest factor: ≤ 4
Line regulation: 0.1% (% of full scale)
Load regulation: 0.5% (% of full scale)
Response time: < 100µS
Reverse current:
30% of Maximum Output RMS Current (Continue)
100% of Maximum Output RMS Current (Within 3 minutes)
Setting
+ Voltage:
Range: 0 ~ 155Vrms, 0 ~ 310Vrms, Auto
Resolution: 0.01V at 0.00 ~ 99.99Vrms 0.1V at 100.0 ~ 310.0Vrms
Accuracy: ± (0.5% of setting + 2 counts)
+ Frequency:
Range: 45 ~ 500 Hz
Resolution: 0.01Hz at 45.00 ~ 99.99Hz 0.1Hz at 100.0 ~ 500.0Hz
Accuracy: ± 0.02% of Setting
+ Power on/off phase angle
Range: 0 ~ 359°
Resolution: 1°
Accuracy: ± 1° (Only 45 ~ 65Hz)
Measurement *3 GW Instek APS-7050
+ Voltage (rms)
Range: 0.20 ~ 38.75Vrms; 38.76 ~ 77.50Vrms; 77.51 ~ 155.0Vrms; 155.1 ~ 310.0Vrms
+ Resolution: 0.01V at 0.00 ~ 99.99Vrms; 0.1V at 100.0 ~ 310.0Vrms
Accuracy *4 ± (0.5% of reading + 2 counts)
+ Frequency
Range: 45 ~ 500Hz
Resolution: 0.01Hz at 45.00 ~ 99.99Hz; 0.1Hz at 100.0 ~ 500.0Hz…
Accuracy: ± 0.1Hz
+ Current (rms)
Range: 2.00 ~ 70.00mA; 60.0 ~ 350.0mA; 0.300 ~ 3.500A; 3.00 ~ 17.50A
Resolution: 0.01mA; 0.1mA; 0.001A; 0.01A
Accuracy
± (0.6% of reading + 5 counts) , 2.00 ~ 350.0mA
± (0.5% of reading + 5 counts) , 0.300 ~ 3.500A
± (0.5% of reading + 3 counts) , 3.000 ~ 17.50A
+ Current (peak)
Range: 0.0 ~ 70.0A
Resolution: 0.1A
Accuracy: ± (1% of reading + 1 counts)
+ Power (W)
Resolution: 0.01W; 0.1W; 1W
Accuracy:
± (0.6% of reading + 5 counts) , 0.20 ~ 99.99W
± (0.6% of reading + 5 counts) , 100.0 ~ 999.9W
± (0.6% of reading + 2 counts) , 1000 ~ 9999W
+ Apparent Power (VA)
Resolution: 0.01VA; 0.1VA; 1VA
Accuracy
± (1% of reading + 7 counts) , 0.20 ~ 99.99VA
± (1% of reading + 7 counts) , 100.0 ~ 999.9VA
± (1% of reading + 5 counts) , 1000 ~ 9999VA
+ Power Factor
Range: 0.000~ 1.000
Resolution: 0.001
Accuracy: ±2% reading + 2 counts
General GW Instek APS-7050
Remote output signal: Pass, Fail, Test-in Process, Trigger in, Trigger out, OUT ON/OFF
Sync output signal: Output Signal 10 V, BNC Type
Number of Preset: 10 (0~9 numeric keys)
Protection: OCP, OPP, OTP and Alarm
Trigger Out: Maximum low level output = 0.8V; Minimum high level output = 2V; Maximum source current = 8mA.
Trigger In: Maximum low level input voltage = 0.8V; Minimum high level input voltage = 2.0V; Maximum sink current = 8mA.
SEQUENCE / SIMULATION FUNCTION
Number of Memories: 10 (0~9 numeric keys)
Number of Steps: 255 max. (for 1 sequence)
Step Time Setting Range: 0.01 ~ 999.99 S
Operation within Step: Constant, Keep, Linear Sweep
Parameters: Ouptut Range, Frequency, Waveform (sine wave only), On Phase, Off Phase, Term Jump Count (0 ~255), Jump-to, Branch 1, Branch 2, Trigger Output
Sequence Control: Start, Stop, Hold, Continue, Branch 1, Branch 2
AC Input
Phase: Single Phase
Input Voltage: 115/230Vac ± 15%
Input Frequency: 50/60Hz
Max. Current: 16A/8A
Power Factor: 0.7 Typ.
Enviromental Conditions
Operating temperature range: 0 ~ +40 °C
Storage temperature range: -10 ~ +70 °C
Operating humidity range: 20 ~ 80% RH (no condensation)
Storage humidity range: 80% RH or less (no condensation)
Interface
Standard: USB Host, LAN
Optional: GPIB (APS-001) RS232 / USB CDC (APS-002)
Dimensions & Weight
Dimensions(mm) (WxHxD): 430x89x400
Weight: 24Kg
Product specifications are subject to change without notice. The Specifications are not suit for ARB mode.
*2 45 to 500Hz, 10% or higher of the rated output voltage, the maximum current or lower *3 All of measurement accuracy is at 23±5°C
*4 In the case of 15 to 155V, 30 to 310V, sine wave, no load
*5 Maximun output current at working voltage 480Vrms
*6 In the case of 60 to 600V, sine wave, no load
*7 45 to 999.9Hz, 10% or higher of the rated output voltage, the maximum current or lower
Introduction GW Instek APS-7050 AC Power Sources
Features GW Instek APS-7050
- 4.3-inch TFT-LCD
- Output capacity : 500VA、310Vrms、4.2Arms; Output augmentation by options (0~600Vrms/45~999.9Hz)
- Low Ripple & Noise
- Measurement and test functions include VOLT、CURR、PWR、SVA、IPK、IPKH、FREQ、PF、CF
- Support a small AC current measurement 2mA ~ 35A, Min. resolution 0.01mA
- Reverse Current Alarm Function
- 10 sets of Sequence function to Edit Output Waveforms/ 10 sets of simulate mode to Rapidly Simulate Transient Power Supply/ 10 sets of Program mode to Define Measurement Sequence/ 10 sets of Panel Memory Function
- Automatic Execution of Sequence、Simulate、Program mode and Output Function when the Power is on
- Optional Interfaces: GPIB (APS-001)；RS-232 / USB CDC(APS-002 for APS-7050 & APS-7100 only)
Review GW Instek APS-7050 AC Power Sources (Programmable Linear)
There are no reviews yet.